The Fundamentals of Plumbing Knowledge When Installing a Bathtub
The Fundamentals of Plumbing Knowledge When Installing a Bathtub
Blog Article
The author is making a number of great annotation on How to Install a Bathtub overall in this article beneath.
Setting up a bath tub isn't specifically rocket science, but it does require strong plumbing, woodworking, and often, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old bathtub is conveniently easily accessible, the project can move speedily; if you need to open a wall surface to get rid of the old tub and position the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub as well as set in the brand-new one. Make sure you have actually certified yourself for the job and are comfortable attempting it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you may require an expert plumber to make tube links.
This post will certainly help you install a brand-new bath tub in your shower room if you have actually already gotten a brand-new tub as well as do not require to change the plan of your previous water supply pipes.
Your tools as well as product list should make up the following:
Planning for the Installment
To start with, the sustaining structure provided with the bath ought to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the versatile tap adapters to the bottom of both faucets using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its final setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any type of water staying in the system. The process of removing the existing faucets can be rather troublesome due to the limited gain access to that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, put the tub in the required setting. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub until the spirit level reads level.
To install taps, fit the bottom of the furthest versatile faucet adapter to the appropriate supply pipe by making a compression join; after that do the exact same for the other faucet.
Switch on the water system and inspect all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also check the overflow outlet and also the typical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the maker's user's manual. Tiling and sealing around the bathtub should wait till the bath tub has actually been utilized a minimum of when as this will settle it into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in place between the faucet and the sink. Protect the faucet in place with the manufacturer offered backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet adapters. The previous type must be linked to the faucet ends initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, leading to issues with dampness and possible leakages to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to permit the activity experienced when the tub is in use. The sealer can break relatively early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our section about Tools You Need to Install a New Bathtub . Thanks a ton for taking time to browse our piece. Sharing is good. Helping people is fun. Thank you so much for going through it.
Article Report this page